-Brand new M/T 33x10.5x15w never mounted -- $400
-Brodix Track 1 heads C&C ported by Kunts & Co. 2.12 in valves, 1.6 ex. Fresh valve job, titanium retainers. Comes w/ ported Edelbrock manifold w/ intake gaskets. Heads have 76cc chambers w/ receiver grooves for o-ringed block. Three cylinders have been welded due to being torched in a blown alcohol combo. They have been professionally repaired. Flow #'s: 321@.600, 335@.650, 346@.700, 359@.800 lift -- $2500
-Yates C-3 Heads, O-ringed, C&C Ported, 41cc Chambers, Titanium valves and retainers, Fresh valve job, Fresh springs, 2.18in, 1.5ex, 265lbs at the seat, complete ready to bolt on. Flow #'s Intake: 216@.300, 262@.400, 314@.500, 350@.600, 370@.700, 354@.800
Exhaust: 138@.300, 189@.400, 213@.500, 228@.600, 239@.700, 245@.800 -- $2500
- Jesel One-Peice girdle (new), Jesel shaft mount 1.65 rockers, 7/16" pushrods, Jesel Tie-Bar offset lifters, all for the Yates heads -- $1900
- SSI 14-71 blower, magnesium case. Standard helix 60 degree rotors, large top (16") opening. This blower needs to be restripped. Everything else looks to be in good condition. I never ran this blower, but bought it w/ a motor that was in a promod car -- $2000
- BAE Fuel Hemi heads, drilled for two sets of down nozzles, comes w/ one set of down nozzle rails. Titanium 2.400" intake, 2.00" exhaust. Fresh springs and retainers. Intake ports measure 2.300 by 2.275. Later design w/ 6 bolt studs for manifold. -- $2000
- MSD Promag 12 P/N8160 CCW rotation w/ rev box P/N 8106, w/ Cap, all bought new at the beginning of the year. Has dyno passes only. Sent to Leahy to get checked a month ago and all checked good. Everything is in new condition. -- $1500
- MSD Promag 12 CCW Generator only, no cap -- $900
- MSD 8105 Points box -- $200
- Hogan sheet metal manifold for a small block ford running cleveland heads w/ 9.5" deck. Manifold is in great shape! Has 1/8"npt bungs welded in each runner for port nozzles, etc. Hogan did all the work. Hogan will build you a custom top if you're going to run carb's, throttle body, etc, for $350. Call Tim at Hogan 805-928-8483 for details on building a top -- $1800
- New Harwood Aero scoop P/N 4166. I bought it new a few months ago, the only thing i've done to it was notch the bottom middle on the front and back to fit flush on a hood -- $225
- Lenco CS1 course spline 1.44 gear set -- $700
- (2) Borla Oval 4" exhaust, one is scrapped up from loading on the trailer, but still works good -- $150
- 2 1/8" Headers w/ fresh jet-hot coating made to fit Yates heads on a 351 SBF in a '68 Mustang -- $300
- HV Oil pump for a small block ford -- $ 75
- Hex-A-Just timing gear set for a small block ford, like new -- $75
- Eagle H-Beam steel rods 6.125" w/ 5 dyno passes only -- $375
- Enderle external fuel pump belt drive, hub has standard 6 bolt blower pulley pattern -- $150
- Procharger 73 tooth crank pulley, multi-purpose drilled for 6 bolt or stock ford dampner 4 bolt pattern, cog only -- $170
I have pictures of everything! Shoot me an email josh@chancetrans.com or call me @ 316-529-1883, or 316-650-0624 on the weekends. Let me know if you have any questions! |