Register
Login
 
 
 

berryplumbing.GIF
  LIMITED STREET


logo-small.png
MODIFIED STREET

hothead-logo.JPG
   5.0 INDEX

Header-1.jpg
   7.0 INDEX

Vengeance 1 copy.JPG
   HOT STREET


 Message Forums
Subject: 400 sbc
Prev Next
You are not authorized to post a reply.

Author Messages
Jimmy User is Offline
Posts:132



02/17/2008 10:03 AM Alert 

WTB 400 SBC BLOCK 4 bolt, nothing over 40 over,  thanks

will consider aftermarket block also

Jimmy O. Johnson
423-838-3115
706-375-4607
Jimmy User is Offline
Posts:132



02/18/2008 7:49 PM Alert 
Posted By Jimmy on 02/17/2008 10:03 AM

WTB 400 SBC BLOCK 4 bolt, nothing over 40 over,  thanks

will consider aftermarket block also


1

Jimmy O. Johnson
423-838-3115
706-375-4607
kiesel User is Offline
Posts:2



02/18/2008 9:03 PM Alert 
have a two bolt block, 4.165 bore.  aligned bored, deck plugged and decked. lifter valley vent holes tapped for vents. clearanced for 4.00 stroke. currently at machine shop being cleaned and new cam bearings installed. ran in 7.0 car and never hurt.

  steve kiesel
Jimmy User is Offline
Posts:132



02/18/2008 10:46 PM Alert 
Posted By Slickskiller on 02/18/2008 10:26 PM
Cuz Do I have the deal for you!!! 406 sb 4.155 bore

For 4500.00 dollars you can get a complete engine carb to oilpan that will put that firebird in the low 6's
Eagle crankshaft
Eagle H beam rods
Wiesco 13.5 to 1 dome pistons
Reed custom cut 700 lift roller cam
lunati lifters, springs, 10 deg. retainers
crane enegizer roller rockers
crane stud girdel
edelbrock 96071 angel plug heads
victor jr intake
750 race demon carb.

 engine runs 7.30s on the motor in a 3700 lb truck you do the math and it will fly in a lighter more aerodinamic car.  i ran this engine about 40 times last year after it was freshend up heck the rings probablly arent even broken in yet


I'll deliver it in the truck ,run it, race it what ever it takes for you to buy it !!
WHATCHA THINK!!!


Need another block only. have every thing else  thanks  got to be lower than a 6 to go where i'm going 

Jimmy O. Johnson
423-838-3115
706-375-4607
Jimmy User is Offline
Posts:132



02/18/2008 10:47 PM Alert 
Posted By kiesel on 02/18/2008 9:03 PM
have a two bolt block, 4.165 bore.  aligned bored, deck plugged and decked. lifter valley vent holes tapped for vents. clearanced for 4.00 stroke. currently at machine shop being cleaned and new cam bearings installed. ran in 7.0 car and never hurt.

  steve kiesel

give me a call 423-838-3115

Jimmy O. Johnson
423-838-3115
706-375-4607
Jimmy User is Offline
Posts:132



02/23/2008 11:12 PM Alert 
Posted By kiesel on 02/18/2008 9:03 PM
have a two bolt block, 4.165 bore.  aligned bored, deck plugged and decked. lifter valley vent holes tapped for vents. clearanced for 4.00 stroke. currently at machine shop being cleaned and new cam bearings installed. ran in 7.0 car and never hurt.

  steve kiesel

good meeting you thanks for the block, Jimmy

Jimmy O. Johnson
423-838-3115
706-375-4607
You are not authorized to post a reply.



ActiveForums 3.6

YearOne Outlaw 10.5 Series

HorsePower

Holley
Contingency Sponsor
Brodix
pro line race engines
NOS
mickey thompson
Hoosier
auto meter
ptc racing
tci
Berry motorsports
Berry Plumbing & Equipment Co.
Pro Photo Productions
pro torque converters
champion system
yearone
outlaw limited street
Sheppard Race Cars
Copyright 2007 by OutlawRacing.com  / Outlaw Racing Street Car Association - Presented by YearOne / 770-652-5190
Terms Of Use / Privacy Statement